- •Features
- •Overview
- •Block Diagram
- •Pin Descriptions
- •Port A (PA2..PA0)
- •Port B (PB7..PB0)
- •Port D (PD6..PD0)
- •RESET
- •XTAL1
- •XTAL2
- •Resources
- •Code Examples
- •Disclaimer
- •AVR CPU Core
- •Introduction
- •Status Register
- •Stack Pointer
- •Erase
- •Write
- •I/O Memory
- •Clock Systems and their Distribution
- •CPU Clock – clkCPU
- •I/O Clock – clkI/O
- •Flash Clock – clkFLASH
- •Clock Sources
- •Crystal Oscillator
- •External Clock
- •Idle Mode
- •Power-down Mode
- •Standby Mode
- •Analog Comparator
- •Watchdog Timer
- •Port Pins
- •Resetting the AVR
- •Reset Sources
- •Power-on Reset
- •External Reset
- •Watchdog Reset
- •Watchdog Timer
- •Interrupts
- •I/O-Ports
- •Introduction
- •Configuring the Pin
- •Toggling the Pin
- •Reading the Pin Value
- •Alternate Port Functions
- •Register Description for I/O-Ports
- •8-bit Timer/Counter0 with PWM
- •Overview
- •Registers
- •Definitions
- •Counter Unit
- •Normal Mode
- •Fast PWM Mode
- •8-bit Timer/Counter Register Description
- •Timer/Counter0 and Timer/Counter1 Prescalers
- •Internal Clock Source
- •Prescaler Reset
- •External Clock Source
- •16-bit Timer/Counter1
- •Overview
- •Registers
- •Definitions
- •Compatibility
- •Counter Unit
- •Input Capture Unit
- •Noise Canceler
- •Force Output Compare
- •Normal Mode
- •Fast PWM Mode
- •16-bit Timer/Counter Register Description
- •USART
- •Overview
- •AVR USART vs. AVR UART – Compatibility
- •Clock Generation
- •External Clock
- •Frame Formats
- •Parity Bit Calculation
- •Parity Generator
- •Receiver Error Flags
- •Parity Checker
- •Disabling the Receiver
- •Using MPCM
- •Overview
- •Three-wire Mode
- •Two-wire Mode
- •4-bit Counter
- •12-bit Timer/Counter
- •Software Interrupt
- •Analog Comparator
- •Features
- •Overview
- •Physical Interface
- •Limitations of debugWIRE
- •debugWire Data Register – DWDR
- •Fuse Bits
- •Latching of Fuses
- •Signature Bytes
- •Calibration Byte
- •Page Size
- •Signal Names
- •Chip Erase
- •Reading the Flash
- •Reading the EEPROM
- •Electrical Characteristics
- •Absolute Maximum Ratings*
- •DC Characteristics
- •External Clock Drive Waveforms
- •Maximum Speed vs. VCC
- •Idle Supply Current
- •Pin Pull-up
- •Pin Driver Strength
- •Register Summary
- •Instruction Set Summary
- •Ordering Information
- •Packaging Information
- •Errata
- •ATtiny2313 Rev C
- •ATtiny2313 Rev B
- •ATtiny2313 Rev A
- •Changes from Rev. 2543H-02/05 to Rev. 2543I-04/06
- •Changes from Rev. 2543G-10/04 to Rev. 2543H-02/05
- •Changes from Rev. 2543F-08/04 to Rev. 2543G-10/04
- •Changes from Rev. 2543E-04/04 to Rev. 2543F-08/04
- •Changes from Rev. 2543D-03/04 to Rev. 2543E-04/04
- •Changes from Rev. 2543C-12/03 to Rev. 2543D-03/04
- •Changes from Rev. 2543B-09/03 to Rev. 2543C-12/03
- •Changes from Rev. 2543A-09/03 to Rev. 2543B-09/03
- •Table of Contents
ATtiny2313
USART
The Universal Synchronous and Asynchronous serial Receiver and Transmitter (USART) is a highly flexible serial communication device. The main features are:
•Full Duplex Operation (Independent Serial Receive and Transmit Registers)
•Asynchronous or Synchronous Operation
•Master or Slave Clocked Synchronous Operation
•High Resolution Baud Rate Generator
•Supports Serial Frames with 5, 6, 7, 8, or 9 Data Bits and 1 or 2 Stop Bits
•Odd or Even Parity Generation and Parity Check Supported by Hardware
•Data OverRun Detection
•Framing Error Detection
•Noise Filtering Includes False Start Bit Detection and Digital Low Pass Filter
•Three Separate Interrupts on TX Complete, TX Data Register Empty and RX Complete
•Multi-processor Communication Mode
•Double Speed Asynchronous Communication Mode
Overview |
A simplified block diagram of the USART Transmitter is shown in Figure 53. CPU accessible I/O |
|
Registers and I/O pins are shown in bold. |
|
Figure 53. USART Block Diagram(1) |
|
|
|
Clock Generator |
|
|
UBRR[H:L] |
|
|
|
|
|
OSC |
|
|
|
BAUD RATE GENERATOR |
|
|
|
|
|
SYNC LOGIC |
PIN |
XCK |
|
|
|
||
|
|
|
CONTROL |
|
|
|
|
|
|
|
|
|
Transmitter |
|
|
UDR (Transmit) |
|
TX |
|
|
|
CONTROL |
|
|
|
|
|
|
|
|
|
PARITY |
|
|
BUS |
|
GENERATOR |
|
|
TRANSMIT SHIFT REGISTER |
|
PIN |
TxD |
|
|
CONTROL |
|||
|
|
|
||
DATA |
|
|
|
|
|
|
Receiver |
|
|
|
|
|
|
|
|
|
CLOCK |
RX |
|
|
|
RECOVERY |
CONTROL |
|
|
RECEIVE SHIFT REGISTER |
DATA |
PIN |
RxD |
|
RECOVERY |
CONTROL |
||
|
|
|
||
|
UDR (Receive) |
PARITY |
|
|
|
CHECKER |
|
|
|
|
|
|
|
|
UCSRA |
|
UCSRB |
UCSRC |
|
Note: 1. Refer to Figure 1 on page 2, Table 29 on page 57, and Table 26 on page 55 for USART pin placement.
111
2543L–AVR–08/10